[1 Area 2,900 Won Event] InMode Lifting

1. Quantitative Treatment for Precise Energy Delivery (FX & FORMA)

InMode's FX (fat reduction) and FORMA (collagen lifting) modes have a set maximum output. Therefore, sufficient time and appropriate energy are important for treatment effectiveness.

For FX mode, the treatment is based on device usage time of 6 minutes or more, and for FORMA mode, it's based on a device energy value of 10K or more.

Our clinic adheres to the principle of quantitative treatment, rather than injecting less energy than the actual standard.

All InMode treatments are performed directly by medical professionals, aiming for both safe and effective results.

2. FX Mode: Know-how for Rapid Temperature Increase and Maintenance

To break down fat using FX mode, it's crucial to raise the temperature above a certain level and maintain it.

To rapidly increase and maintain temperature while minimizing pain, our clinic utilizes the following methods:

During treatment, we meticulously adjust output settings, suction pressure, speed control, treatment sequence, and skin response.

- We utilize high output within an appropriate range. This supplies more powerful energy, allowing the skin temperature to rise quickly.

- We apply longer pulse durations. By increasing the radiofrequency injection time per session, we extend the thermal penetration time of the energy delivered by the tip, helping to raise the temperature more rapidly.

- We frequently check the temperature of the treatment area with the back of the hand. In addition to the InMode device's real-time temperature measurement function, medical staff directly check the temperature of the patient's treatment area with the back of their hand to minimize pain as much as possible.

- We meticulously adjust the movement speed for each area. In the initial stage of treatment, heat is distributed evenly across the entire skin, then concentrated on specific areas with more fat or areas of concern to raise the temperature. This is done to reduce the burden of pain while also considering treatment effectiveness.

3. Meticulous Design Treatment to Minimize Cheek Hollowing

Since FX treatment is a process that reduces fat, careful design planning is absolutely necessary before the procedure.

Over-treatment can lead to cheek hollowing, so for asymmetry improvement or areas of concern to the patient, we consult thoroughly with the director and design the treatment before proceeding.

We carefully consider each individual's face shape and fat distribution to ensure natural improvement.

4. Quantitative Verification for Transparent Treatment

After the treatment is completed, we directly show patients that the actual treatment time and energy were quantitatively applied. This is a process to ensure accurate treatment and build trust.

Kkeuthan Clinic's InMode

Radiofrequency (RF) lifting treatment methods can be broadly classified into two types:

1. Monopolar

This method sends energy from one electrode and recovers thermal energy through a pad attached to the body.

Energy is delivered to deep skin tissues, allowing for deep heat effects, but some irritation may be felt during treatment.

2. Bipolar

Energy circulates between two electrodes, concentrating heat on the skin surface and dermal layer.

While it has less pain and is relatively safe, thermal energy may find it difficult to reach relatively deeper fat layers.

*How does InMode FX work on the fat layer despite being a bipolar method?

As explained earlier, it is difficult for conventional bipolar methods to deliver energy to the fat layer.

However, InMode FX possesses a special structure that allows it to effectively target the fat layer despite being a bipolar method.

The secret lies in InMode FX's vacuum suction function.

During treatment, the skin is gently suctioned, like being drawn in, positioning the skin and subcutaneous fat layer between the two electrodes.

When radiofrequency is delivered in this state, heat can efficiently penetrate to deeper layers, even with a bipolar method.

When treated in this manner, degeneration of fat cells can be induced at temperatures of approximately 42-45 degrees Celsius, and

Damaged fat cells are naturally expelled through lymphatic circulation. Simultaneously, collagen production is promoted in the dermal layer,

allowing for both fat reduction and skin elasticity improvement to be expected simultaneously.

*Expected effects of InMode FX

1. Fat Reduction Effect

If a constant heat of 42-45 degrees Celsius or higher is maintained for at least 6 minutes, the cell membranes of fat cells can be damaged.

The contents of damaged fat cells are naturally expelled from the body.

For areas with significant fat accumulation, such as the cheeks or double chin, fat decomposition procedures can be considered.

2. Inducing Collagen Production

Along with the process of reducing fat cells, heat is delivered to the dermis, aiding in the activation of fibroblasts. This can lead to the expectation of new collagen production.

Existing collagen shows a contraction response, providing an immediate skin tightening effect, which can aid in lifting.

*Expected Effects of InMode Forma

Forma is a radiofrequency (RF) treatment that delivers thermal energy to the dermis, which is a relatively shallower layer than the fat layer.

By gently moving the device over the skin surface, a temperature of 42~43℃ is delivered to the dermis.

During this process, fibroblasts are activated, which can help improve fine lines, enlarged pores, and reduced skin elasticity.

Forma features a real-time temperature feedback system, allowing for stable and continuous temperature maintenance during the procedure.

This helps induce collagen production with consistent thermal energy while minimizing excessive skin damage.

Immediately after the procedure, the skin may feel tightened due to contraction, followed by a gradual collagen production process over 2 to 6 weeks.

*FX and Forma: Which areas are suitable for application?

Sagging or excessive fat in various areas of the face can result from multiple complex causes.

– Double Chin

Double chins often result from excessive accumulation of subcutaneous fat or decreased elasticity of the muscles beneath the jaw.

The FX treatment targets the fat layer in this area, delivering radiofrequency thermal energy to reduce fat cells and induce collagen production, which can help improve the elasticity of the skin under the chin.

If you have a double chin with thin or significantly less elastic skin, Forma can be combined for additional elasticity improvement.

– Cheeks below the cheekbones (Jowls)

Cheeks below the cheekbones are a sign of mid-face aging, occurring as the fat in the cheek area sags downwards with age. FX can be used to reduce the amount of such unwanted fat.

If Forma is added to enhance skin elasticity, an overall improved facial contour can be expected.

– Cheeks/Side Cheeks

Enlarged pores, fine lines, and rough skin texture are changes primarily resulting from a decrease in collagen density in the dermis.

Forma activates fibroblasts through thermal energy, inducing the production of collagen and elastin. This can help improve skin surface density and texture.

– Jawline

The main reason a sharp jawline becomes less defined is often due to decreased skin elasticity rather than fat issues. In such cases, Forma can be used to deliver focused heat to the dermis, inducing collagen contraction and production.

If FX treatment is combined as needed, it can help create an even more defined facial contour.

– Eye Area, Forehead, Mouth Area

These areas are prone to fine lines and are characterized by thin, sensitive skin.

Forma can achieve desired changes with relatively low energy, making it a suitable option when considering procedures for such sensitive areas.

*Importance of InMode Treatment

The satisfaction with InMode treatment results is difficult to guarantee simply by possessing the equipment.

The selection and combination of handpieces, the depth of thermal energy delivery, the total cumulative energy, and delicate customized treatment tailored to each individual's skin condition must be carefully considered.

For example, in Forma treatment,

Merely delivering a warm sensation to the skin is unlikely to induce collagen production.

In fact, a temperature of 42~43℃ must be continuously maintained in the deep dermis for at least 10 minutes.

Only when a cumulative energy of 8~12kJ or more per area is sufficiently reached can fibroblasts be activated and collagen production be induced.

Similarly for FX treatment, it can be more effective when vacuum suction and thermal energy are applied together, rather than simply delivering radiofrequency energy alone.

Deep heat of 42℃ or more must be appropriately delivered for at least 6 minutes to simultaneously expect fat cell reduction and collagen contraction.

Depending on the characteristics of the treatment area, 8~15kJ or more of energy must be delivered, and for areas with thin skin or prone to bruising, the vacuum pressure also needs to be delicately adjusted.

The method of first reducing fat cells with FX treatment and then performing a final lift with Forma is likely to yield more satisfying results.

While controlling swelling and heat reactions that may remain on the skin after the procedure, it contributes to refining the lifted facial lines.

In summary,

InMode treatment goes beyond simply choosing equipment; the deep anatomical knowledge of the medical staff performing the procedure, their ability to precisely adjust settings, and their skill in designing delicate, customized treatments for each individual play a crucial role.

At our clinic, we adhere to the principles emphasized above, constantly researching and striving to provide satisfactory lifting results.

Even with the same InMode procedure, we strive to enhance patient satisfaction through a customized approach that considers each individual's unique characteristics.

Treatment Process

Step 1 FX is performed using a combination of radiofrequency energy and IRE (electrical stimulation) technology. This step can act on various skin depths, from the epidermis to the SMAS layer, contributing to the reduction of unnecessary fat cells. Simultaneously, it can help improve facial contours by promoting collagen regeneration.

Step 2 FORMA is a procedure that stimulates collagen production by delivering appropriate heat to the dermis. Through this, you can expect effects such as improved skin wrinkles and enhanced overall elasticity.

The entire treatment process is personally performed by experienced medical staff.